askelectronics

Hi,...

I have to fix a slightly very stupid mistake that I’ve made....

I have two led strips used for 2x27" monitor bias lighting. Each have their own USB cables for power. These two USB cables are plugged into a 2-port wall charger for a phone. I would like to use a 2x female to 1x male adapter to join the two USB cables into one, then plug it into a much smaller 1-port USB wall charger. The...

Hi, I have built a microvawe transformer spotwelder, I have put a single turn of welder wire for in the secondary and I’m timing it with arduino. Worth mentioning it was/is a 230V transformer. Electrodes are sharpened copper rods. I believe the voltage is still high. The spotwelds it produces are slightly discolored and not as...

Currently, only one company in the world – ASML – has the technological capability necessary for the creation of photolithography machines which are sufficient for the production of modern semiconductor devices. What I’m wondering is at what point does semiconductor manufacturing become practical, or even feesible for...

Hi!...

Hello y’all! I’ve always been interested in computers and programming for as long as i can remember, but recently i’ve decided to try to get into some of the deeper stuff behind that, into the wonderful world of electronics. Where should I start? What courses or books or youtube series should I consume? What are some...

Hey folks, I have a Mackie 802-VLZ4 mixer which does this narsty pop when you turn it on; I’m pretty sure it’s what killed one of the woofers in my monitors. It has been put out of service and I will either harvest its many through-hole organs or else fix it....

So I’m a refrigeration tech with some electronics manufacturing experience. But I’ve never combined the 2 skillsets so I’ve been toying with the idea of building a large vapor chamber to cool a computer via direct immersion in a refrigerant. I know its about as far from practical as you can get but it sounds like fun....

My project is a “breathing” white 12v LED strip controlled by an esp32 on a dev board, and switched with an IFLZ44N mosfet....

I have some metal film 1/2w 2.2ohm resistors in some car wiring. I’m concerned about the durability of this install and am seeking advice on how to protect the resistor once it’s soldered in place. The obvious is heat shrink tubing, but it’s there anything more substantial?...

Hello! I bought 30 simple UV leds (those with a big and a small leg, not a single strip). I’m trying to build a UV station to dry my resin but idk how to proceed. I tryed watching some videos but there is a lot of math to build that and I can’t do it. I have 30 led lights, 5 resistors of 100 and 5 of 300. I wanted to use AA...

I’m trying to use an RPi Pico W as a temp/humidity sensor using a DHT20....

I’ve recently acquired an uncalibrated Philips PM2534 (edit: the battery-backed factory calibration data was lost due to the battery running out). I’m looking into somehow getting it calibrated. However, the calibration procedure is rather involved, and requires such things as an exact 300V DC (the service manual recommends...

I want to change te battery setup in the camper van a bit....

Hey friends,...

The lower part of my screen is updated one frame earlier than the upper part. I was able to isolate the error to the HDMI output of my laptop. The screen or cable is not broken, as I don’t get these errors with other connected devices. I am assuming it is some hardware defect. Does anyone know what it could be and how I could...

I’m trying to build a esp8266 weather station and got some MCP1700-3302E to power the esp8266 from a lipo. But when I connect the lipo to the MCP1700 (looking at it flat spot at the front, ground left, Vin in the middle and Vout on the right) I get no output at Vout. I googled and could not find anything. I tested 5 different...

Questions:...

It’s the handle of a water kettle. Behind the circuit board is nothing. There is also no other circuit board in the kettle. Is the yellow thing the beeper? Thanks for any help 🙏

Hi, this post is structured similarly to r/PrintedCircuitBoard 's review request format. Since we don’t have any PCB communities over here yet, I thought that this might fit in here and can maybe spark some friendly discussion....

Solution: @DJPhil has made some really insightful comments below, which are really useful. If you just want the cap you can set the parametric searches for 660uF, or in September 2023 I’ve found that digikey stock(s/ed) chemi-con EKHJ451VSN661MA59M....

So I’m doing some testing of USB-C cables using a tester and a constant load (I’ll have another post soon with some questions on this). But before running each test, I’m checking the E-mark chip and then enumerating the charge capabilities of each to see what they report being capable of....

Hello,...