askelectronics

I recently came to the realization that I’ve been kinda punishing myself with cheap no-name solder that is really difficult to work with....

It’s the handle of a water kettle. Behind the circuit board is nothing. There is also no other circuit board in the kettle. Is the yellow thing the beeper? Thanks for any help 🙏

Hi, I have built a microvawe transformer spotwelder, I have put a single turn of welder wire for in the secondary and I’m timing it with arduino. Worth mentioning it was/is a 230V transformer. Electrodes are sharpened copper rods. I believe the voltage is still high. The spotwelds it produces are slightly discolored and not as...

Im building a flashlight and i want to test if a fan in it would be a good idea but the flashlight is really small so i would need a motor thats smaller than 1 cm preferably. I found really good ones at maxon group but unless you order them in bulk(1000+ units) they cost like 400€. So do yall know anywhere i could find them?...

Hello y’all! I’ve always been interested in computers and programming for as long as i can remember, but recently i’ve decided to try to get into some of the deeper stuff behind that, into the wonderful world of electronics. Where should I start? What courses or books or youtube series should I consume? What are some...

So, there are these great 32700 LiFePO4 batteries that showed up in my local industrial market. For like USD 2$!...

Hey friends,...

My project is a “breathing” white 12v LED strip controlled by an esp32 on a dev board, and switched with an IFLZ44N mosfet....

I have a 3D printer and have a special filter that has two 24V blower fans that are connected in parallel. Unfortunately my printer doesn’t have the proper connectors for the fans. So if I purchase something like this power jack adapter I know the adapter is 12V not sure if that would make a difference. Anyway if I connect the...

I am curious if one, something like this exists, and two what the cost might be? I am looking for a screen, I assume an e-ink is the best/cheapest option and I want it to be as close as possible to the size of a playing card, ideally not thicker than 2MM. But I think up to 5mm could work....

I want to replace one half of this with longer wire, but I am not confident about the name of the connector used....

Does anyone recognise these power supplies? They’re cheap AliExpress led drivers and I want to change its output voltage to around 22V from 12V. I’ve read that the way to do this is to adjust the REF voltage on the IC that controls it. It’s a KA3845 but I don’t understand where that reference voltage is regulated. One...

I have two led strips used for 2x27" monitor bias lighting. Each have their own USB cables for power. These two USB cables are plugged into a 2-port wall charger for a phone. I would like to use a 2x female to 1x male adapter to join the two USB cables into one, then plug it into a much smaller 1-port USB wall charger. The...

I’m trying to use an RPi Pico W as a temp/humidity sensor using a DHT20....

I’ve recently bought a used computer, and it has a few problems. I’m looking for a guide to help me identify which parts are causing the problem....

Currently, only one company in the world – ASML – has the technological capability necessary for the creation of photolithography machines which are sufficient for the production of modern semiconductor devices. What I’m wondering is at what point does semiconductor manufacturing become practical, or even feesible for...

The lower part of my screen is updated one frame earlier than the upper part. I was able to isolate the error to the HDMI output of my laptop. The screen or cable is not broken, as I don’t get these errors with other connected devices. I am assuming it is some hardware defect. Does anyone know what it could be and how I could...

I’m trying to build a esp8266 weather station and got some MCP1700-3302E to power the esp8266 from a lipo. But when I connect the lipo to the MCP1700 (looking at it flat spot at the front, ground left, Vin in the middle and Vout on the right) I get no output at Vout. I googled and could not find anything. I tested 5 different...

Disclaimer: this is not specifically for a commercial product, but various things I design sometimes get commercialized. I mention this so that you may decide whether you want to weigh in. If it’s commercialized, I will probably make very little money but a bunch of university students may get a neat STEM program in the...

Hello,...

Some years ago, before LEDs were a thing, I bought an Ultrafire WF-500 Flashlight that features a Xeon light bulb. As you might imagine the bulb reached its lifetime and burned away....

I have to fix a slightly very stupid mistake that I’ve made....

I have some metal film 1/2w 2.2ohm resistors in some car wiring. I’m concerned about the durability of this install and am seeking advice on how to protect the resistor once it’s soldered in place. The obvious is heat shrink tubing, but it’s there anything more substantial?...

I’ve recently acquired an uncalibrated Philips PM2534 (edit: the battery-backed factory calibration data was lost due to the battery running out). I’m looking into somehow getting it calibrated. However, the calibration procedure is rather involved, and requires such things as an exact 300V DC (the service manual recommends...