I work on equipment that runs off 3 phase 208V but it uses uses a transformer to drop it down to 120V for most of the controls. On this equipment I noticed that there are two fuses on the lines exclusively feeding the 208V side of the transformer and a fuse directly off of the hot side on the 120V side of the transformer....
Working on a joystick. Seems like any protocol I use to read from peripherals is going to be bottlenecked by having just one input. My microcontroller might have multiple ADCs, but there’s just one processor stepping through them. Same for spi, or i2c, or uart. There’s really only ever one sensor reporting back its data at a...
Hello altogether, I guess everybody has some USB-C cables lying around, but wonder if it’s 3A, 5A, 3.0, TB… Anybody able to recomment a device able to determine that? Maybe also something that can be combined with a load tester.
Since MOSFETs have a gate capacitance you’d want to limit the inrush of current from the output of a microcontroller to prevent it from getting damaged prematurely. That’s what gate resistors are usually good for....
I’m an EE by trade focusing on embedded devices, but most of my work is in relatively low-power STM32 applications. When I stopped following developments in hobby kits, it was mostly Arduino Unos slowly driving I2C OLED displays....
Just exploring about this tp-link XN020-G3v router. I’m mostly interested in connecting to the UART, won’t be tinkering with electronics of it, but out of curiosity I tried to search what these chips are. and I couldn’t find much about the big chip. Can anyone describe the 4 main chips on it ? Best would be datasheet, but...
I migrated here in the US (specifically in San Bernardino, CA). Quick Intro: I’m a graduate electrical engineer; honestly, I really don’t have that much experience and not even a decent internship experience due to covid, resulting in an online OJT. Do you think doing an internship here in the US is the way to go? If yes,...
My Google-fu has completely failed me. I’ve got an RGB addressable led curtain. It has 20 strings of 20 LEDs in a square arrangement. I initially assumed it had a wire feeding led data back up, to go to the next drop. On checking however, they are T jointed....
To all the electronic nerds out there: I am trying to trigger a 555 timer by movement in a random direction that also occurs randomly and any change in position should trigger the 555. AFAIK tilt switches are not useable here. Does this idea make sense?...
Im building a flashlight and i want to test if a fan in it would be a good idea but the flashlight is really small so i would need a motor thats smaller than 1 cm preferably. I found really good ones at maxon group but unless you order them in bulk(1000+ units) they cost like 400€. So do yall know anywhere i could find them?...
I have a 3D printer and have a special filter that has two 24V blower fans that are connected in parallel. Unfortunately my printer doesn’t have the proper connectors for the fans. So if I purchase something like this power jack adapter I know the adapter is 12V not sure if that would make a difference. Anyway if I connect the...
I have two led strips used for 2x27" monitor bias lighting. Each have their own USB cables for power. These two USB cables are plugged into a 2-port wall charger for a phone. I would like to use a 2x female to 1x male adapter to join the two USB cables into one, then plug it into a much smaller 1-port USB wall charger. The...
Hi, I have built a microvawe transformer spotwelder, I have put a single turn of welder wire for in the secondary and I’m timing it with arduino. Worth mentioning it was/is a 230V transformer. Electrodes are sharpened copper rods. I believe the voltage is still high. The spotwelds it produces are slightly discolored and not as...
Currently, only one company in the world – ASML – has the technological capability necessary for the creation of photolithography machines which are sufficient for the production of modern semiconductor devices. What I’m wondering is at what point does semiconductor manufacturing become practical, or even feesible for...
Hello y’all! I’ve always been interested in computers and programming for as long as i can remember, but recently i’ve decided to try to get into some of the deeper stuff behind that, into the wonderful world of electronics. Where should I start? What courses or books or youtube series should I consume? What are some...