nilclass

@nilclass@discuss.tchncs.de

This profile is from a federated server and may be incomplete. Browse more on the original instance.

nilclass,

Traffic has trouble in urban areas with a lot of trees

nilclass,

Public transport, and bike lanes

nilclass,

Make one of those apps Wikipedia and you won’t have that issue

nilclass,

I expected this to be a rickroll. Got diappointed.

Looking for really small motors

Im building a flashlight and i want to test if a fan in it would be a good idea but the flashlight is really small so i would need a motor thats smaller than 1 cm preferably. I found really good ones at maxon group but unless you order them in bulk(1000+ units) they cost like 400€. So do yall know anywhere i could find them?...

nilclass,

Try searching for “coreless motor”, gives me lots of ebay results with tiny 7mm diameter dc motors looking like this: external-content.duckduckgo.com/iu/?u=https%3A%2F…

nilclass,

You could give PJON a try github.com/gioblu/PJON

nilclass,

You could probably increase the 82K and 10K resistors to be much bigger

That’s what I thought initially, but this stackoverflow post dissuaded me. The argument there is that the measurement will be wrong, if the input current is not enough to charge the internal cap within the measurement period. But I’ve done some testing now, and measurements done with 820k and 100k agree well with what my voltmeter measures, so I’ll go with this solution!

a fresh alkaline 9V battery is actually 9.6V or more, not 9V.

Indeed! 9.6V * 10k/92k = 1.04V is still below 1.1V, so I should be fine in this case :)

9V battery voltages droop noticeably when under load because of their high internal resistance. Make sure to measure under the same conditions.

This is a good point!

My firmware will be pretty monotonic though, basically:

  1. wake up
  2. measure battery
  3. measure some other sensors (the actual task of the device)
  4. turn on a transceiver, send all the measurements (including battery voltage)
  5. turn off transceiver & go to sleep

So, the load should be always the same at step (2).

nilclass,

Hm, I don’t understand how this is supposed to work - is that a n-channel or p-channel FET?

When I sketch it using falstad’s circuitjs, it looks like the FET (n-channel) is a little bit on all the time

https://discuss.tchncs.de/pictrs/image/dae3ca56-da12-4a48-a023-d3c08c614efb.png

and fully on, when a pulse is applied

https://discuss.tchncs.de/pictrs/image/e929b967-601c-4796-8b42-1f17de54f037.png

Source:

spoiler$ 1 0.000005 10.20027730826997 50 5 43 5e-11 r 144 80 144 176 0 1000 r 0 192 96 192 0 100 t 96 192 144 192 0 1 -8.999999980890745 9.099999980846458e-10 100 default c 144 176 304 176 0 0.000001 -1.7996761414451612e-8 0 f 304 176 384 176 32 2 0.02 d 304 80 304 176 2 default r 384 192 384 272 0 1000 r 384 272 384 352 0 1000 g 384 352 384 384 0 0 g 144 208 144 256 0 0 w 144 80 304 80 0 w 384 160 384 80 0 w 384 80 304 80 0 v 528 256 528 208 0 0 40 9 0 0 0.5 w 528 256 528 352 0 w 528 352 384 352 0 w 528 208 528 80 0 w 528 80 384 80 0 g -48 208 -48 256 0 0 R -48 176 -48 128 0 0 40 5 0 0 0.5 S 0 192 -48 192 0 0 false 0 2 p 384 272 272 272 3 0 0 g 272 272 272 304 0 0___

nilclass,

Could you do similar to diagram 2, but instead of an N-FET use a P-FET between the battery and first resistor in the potential divider?

That’s a great idea! Unfortunately I don’t have a P-FET lying around, so cannot try it right now.

Or use a zener/TVS diode instead of second resistor to clamp the voltage instead of dividing (more robust).

Not sure I understand this point. Which resistor would you replace with a diode?

nilclass,

Nice, than you for sharing!

I won’t be using this for my measurement issue (the other options are much simpler, and i was aiming for less parts, not more), but I’ll do some experiments to familiarize myself with bootstrapping

nilclass,

Best not to eat it.

dang... what else to do with the leftovers then?

nilclass,

good to know for the future!

Can anyone help how to fix my led?

Is there a way to figure out my LED board and fix it myself? I got this LED light which works perfectly but the issue is the usb charger port on the left is not working for whatever reason. There are two ports one micro for charging the led and one usb for outlet charging. Is there a way to switch the charging to the usb port?...

nilclass,

Could you share a picture? I’m having trouble imagining what you are describing

nilclass,

Is that a map they are standing on?

  • All
  • Subscribed
  • Moderated
  • Favorites
  • •
  • localhost
  • All magazines
    •
    Loading…
    Loading the web debug toolbar…
    Attempt #