askelectronics

Currently, only one company in the world – ASML – has the technological capability necessary for the creation of photolithography machines which are sufficient for the production of modern semiconductor devices. What I’m wondering is at what point does semiconductor manufacturing become practical, or even feesible for...

I have some metal film 1/2w 2.2ohm resistors in some car wiring. I’m concerned about the durability of this install and am seeking advice on how to protect the resistor once it’s soldered in place. The obvious is heat shrink tubing, but it’s there anything more substantial?...

Hello! I bought 30 simple UV leds (those with a big and a small leg, not a single strip). I’m trying to build a UV station to dry my resin but idk how to proceed. I tryed watching some videos but there is a lot of math to build that and I can’t do it. I have 30 led lights, 5 resistors of 100 and 5 of 300. I wanted to use AA...

Hello y’all! I’ve always been interested in computers and programming for as long as i can remember, but recently i’ve decided to try to get into some of the deeper stuff behind that, into the wonderful world of electronics. Where should I start? What courses or books or youtube series should I consume? What are some...

So I’m a refrigeration tech with some electronics manufacturing experience. But I’ve never combined the 2 skillsets so I’ve been toying with the idea of building a large vapor chamber to cool a computer via direct immersion in a refrigerant. I know its about as far from practical as you can get but it sounds like fun....

I’m trying to use an RPi Pico W as a temp/humidity sensor using a DHT20....

I’ve recently acquired an uncalibrated Philips PM2534 (edit: the battery-backed factory calibration data was lost due to the battery running out). I’m looking into somehow getting it calibrated. However, the calibration procedure is rather involved, and requires such things as an exact 300V DC (the service manual recommends...

I want to change te battery setup in the camper van a bit....

I’m trying to build a esp8266 weather station and got some MCP1700-3302E to power the esp8266 from a lipo. But when I connect the lipo to the MCP1700 (looking at it flat spot at the front, ground left, Vin in the middle and Vout on the right) I get no output at Vout. I googled and could not find anything. I tested 5 different...

Questions:...

Hi, this post is structured similarly to r/PrintedCircuitBoard 's review request format. Since we don’t have any PCB communities over here yet, I thought that this might fit in here and can maybe spark some friendly discussion....

I am powering a 5V microcontroller (arduino clone, atmega328p) using a 9V block and a buck converter. Now I want to let the microcontroller occasionally measure the battery voltage, so I can get an idea of how full it is....

Hello,...

So I’m doing some testing of USB-C cables using a tester and a constant load (I’ll have another post soon with some questions on this). But before running each test, I’m checking the E-mark chip and then enumerating the charge capabilities of each to see what they report being capable of....

Disclaimer: this is not specifically for a commercial product, but various things I design sometimes get commercialized. I mention this so that you may decide whether you want to weigh in. If it’s commercialized, I will probably make very little money but a bunch of university students may get a neat STEM program in the...

I want to power this board with a 14v battery. The board has a 1s battery connector that can power the board and read the voltage via ADC. Is there something I could place between the two to lower the voltage and still have a battery voltage reading? I would not be charging the battery through this. The usb port would not be...

I want to use an IC that will take x4 3.0 PCIe lanes, and adds a USB 3.1 controller....

Hi, my cousin has an Xbox Series S, and anytime he would move it the fan would make some pretty freaky noises....

Hey all, have I damaged this xbox 360 controller circuit board beyond repair?...

I am curious if one, something like this exists, and two what the cost might be? I am looking for a screen, I assume an e-ink is the best/cheapest option and I want it to be as close as possible to the size of a playing card, ideally not thicker than 2MM. But I think up to 5mm could work....

Is there a way to figure out my LED board and fix it myself? I got this LED light which works perfectly but the issue is the usb charger port on the left is not working for whatever reason. There are two ports one micro for charging the led and one usb for outlet charging. Is there a way to switch the charging to the usb port?...

I am making a graphics card on the tang nano 20k board. I tried synthesising the design in the official IDE and it output:...

Hello! What would be a good way to learn about electronics in terms of creating them? I’m particularly interested in building my own keyboards and other PC peripherals, but I’m not sure what tools I would need, or what’s a good knowledge base if I run into any issues. Any tips and or suggestions?

In a transformer, why are both coils apart from each other? Wouldn’t make more sense to have the ferrite core (tube shape), wind the primary coil around that and then wind the secondary coil on top of the primary? So that the magnetic fields are as close to each other as possible?

Serious question from a beginner in electronics. For reasons I do not fully understand, I have become fixated on the idea of collecting small amounts of electricity from “interesting” sources. I don’t mean “free energy”, instead, I mean things like extracting a few mV from being so close to a AM radio tower using two...