askelectronics

Thanks for all your votes and comments. From the icons that were submitted as requested, the results were as follows:...

My wife gifted me this super cute mini miffy diorama from a gachapon. It uses two 1,5V cells and has a tiny led in it. I would really love to to add a 24h timer. ( it should stay on for 4 hours after turning it on then go to “standby” for 20h before turning back on) Do you guys think an attiny85 is the right thing for the...

Hi everyone! Recently I have gotten interested in communication protocols and have been looking for one (with little success, hence my question) which would satisfy the following requirements (in prioritized order):...

I purchased an e-bike which was advertised as just needing the batteries replaced. The li-ion batteries had been sitting dead for months. Once I got the battery removed it was clear that was not the case. You can see the hole where the plastic melted from this component overheating on the board. The burnt one is the same as...

I replaced my laptop’s battery after it was swollen. I found out that services like call2recycle do not take swollen batteries since they are potentially hazardous material. How can I get rid of that damned spicy pillow? In Dallas. Thanks....

Hello, I have a circuit that will need to return connected hardware to a default state if power is lost. The hardware can handle continuous voltage, so I’m thinking a simple solution would be to use a battery to provide that fallback power source. To avoid draining the battery, I’d like to connect it through a relay on the...

Hey everyone,...

I’m trying to use an LIS2MDL ic with an Arduino nano on a custom PCB designed in KiCad. I tried the Arduino example compass script for the ic and it didn’t work. It just prints “Magnetometer Test” and nothing else happens

Do any of you have experienced good products for tinkering together with a 3 year old?...

Pretty basic question but I am struggling to find the words to get the correct search result. The soldering iron I bought came with very narrow tips that I think are supposed to be used for circuit boards and components....

I’m curious and am playing around with a new EDA tool and am looking at practicing by designing a PCB which should be roughly 28x26mm footprint (give or take a few mm…)....

As the title says, I’m looking for a Linux/macOS-compatible EPROM programmer. I’d like to be able to program parallel (E)EPROMs in the 27xxx range. The newer XGecu programmers seem to not be compatible with Linux/macOS, and the selection of TL866(II) clones is too overwhelming for me to be able to choose one....

Hello! Someone suggested this "If the MOSFET is put into diode connection mode (connect the gate to the drain), you can force a small current (I recommend 1 uA–10 uA; 1 mA would probably be OK; 100 mA would result in significant power dissipation and could influence the results) and record Vds (which is equal to Vgs in this...

Is there a reason why the banner and logo of this community are just the reddit logo?...

Hello, we are making a thesis where we use MOSFETs as an alternative radiation detector. So to explain it, it works when the mosfet is irradiated with an external radiation source; its voltage threshold increases, which will be used to determine the radiation dose. I'm currently asking for help on how we measure the voltage...

I’m trying to replace the jet engine fan inside the PSU of a Nu 1.1 with a Noctua equivalent and am having trouble identifying the connector. The PSU is a Delta Electronics Model EDPS-250AB A, Part Number 400-5494-91....

Hi! I'm working on an arduino project that has a -12v/0v/+12 psu. +12 is fed directly into arduinos voltage regulator, so there's also a +5v line available. I need to convert a -5v+5v signal to 0v+5v to feed it into arduinos analogue input and I've already mocked up a schematic in circuitjs based on an opamp that seems to do...

https://discuss.tchncs.de/pictrs/image/e2575314-be01-4a3f-bab2-cc75811b3ce8.png...

Hi!...

I lost my electric fence tester, probably the pigs ate it. But I opened it once to resolder the earth wire and found it’s really just a voltage divider with resistors and leds, so I can probably rebuild with stuff I have. What resistor values though? 2k to 10k V run through the fence. If any of you good people have a diagram,...

If I wanted to make a USB desk fan from a spare CPU fan (input: 12V, 0.15A), could I just solder a resistor to the positive lead of the USB wire? I plan on getting an adjustable voltage booster, but I was curious if this was possible. I think I would need a 13 ohm resistor for USB 3.0.

I want to connect five OV2640 cameras via FPC to an ESP32 on a custom PCB. Is this generally possible and does the ESP32 have enough power for this or do I need an ESP32 for each camera? The frames per second are not so important as the cameras will be used as QR code scanners. Which components allow to run so many cameras with...

I tried adding an AUX jack to a car stereo with an internal CD player and no native support for one....

I’m looking for a version of this connector (2x2, 2.54mm):...

I have a 12v 6.67A power supply with a male co-axial plug (with centre pin) that’s 7.4mm OD and 5.08mm ID. The metal tube is 12.5mm long....