I'm working on adding extra access control to elevator calling buttons and i would like to identify the connector type of the wires connecting elevator buttons to the elevator panel...
Maybe you can use this to find more connectors that could match yours: connectorbook.com/identification.html?m=NT&n=lo_p…It has a pretty handy identification tool (you can even browse by pictures). It usually suggests quite an amount of connectors but it can guide you in the right direction and you can look at the according datasheets to find out more. By the way the creator of this community made that homepage and a book related to it (or probably the other way round 😅).
It actually depends, on longer posts they somehow disturb the reading flow for me (because they are kind of distracting compared to plain text). For short comments on the other hand I like them and find them rather refreshing.
They are called soft termination, I’m not sure if that’s available for every component, it came to my attention on ceramic caps. It’s a dedicated feature you can filter components e.g. on Digikey.
I’d say that’s a version of a soft termination capacitor. They are used when there’s risk the board is flexed or exposed to mechanical or thermal shocks to prevent cracks in the capacitor (causing it to fail short).
Maybe this: www.microchip.com/en-us/product/PCI11400Unfortunately to access the whole datasheet you might have to sign an NDA (and probably have a large company), also designing things with those kinds of interfaces isn’t trivial.
I’m currently working on a more complex project that uses double sided assembly (and a weird USB-C connector). To practice these things a little, I ordered some low cost boards to get used to that connector and explore double sided reflow (which seems easier than I expected)....
I don’t have it for that long but I didn’t have problems so far, I’m usually only making rather small PCBs tho. I did make some recommended modifications like replacing the paper insulation tape with a kapton tape, proper grounding and flashed another firmware.
I did only use a small hotplate and/or a hotair station, so it seems to be definitely a stepup here 😌.
Yeah I have such a small, cheap Chinese one (T962) that I modified and flashed a nicer firmware on.
I basically populated the bottom side (with more components) first after applying solder past with a stencil, then reflowed the board. After cooling down I applied the solder paste to the upper side (with the LED) by using a small needle on a syringe (because using a stencil was too weird since the board wasn’t laying flat) but since the pads are relatively large and not that many that worked fine. Then I placed the components on that side and simply run the reflow cycle again.
I started with the bottom side because there are no heavy components. I expected heavy parts to just fall off on the second reflow cycle so I tried to avoid that.
At the end I manually assembled the USB connector using a regular soldering iron and tons of flux gel.
I was kind of afraid of SMD things in general a long time but I discovered they are (up to a certain size, 0603 is still okay for hand assembly if you’re patient) comfortable to work with. Even QFN packages are okay if you have access to a hot-air station. I did actually order an BGA sensor out of curiosity along with other things, looked at it and was like “hahaha, thanks, I probably better don’t design that thing into my circuit” (I think it’s a 5-WLCSP package).
Hello, I did manage to kill my cheap-ish bench supply causing it to randomly output up to like 300% the set voltage when under load which did already kill one board. Probably I didn’t actively kill it but the chinesium did its job 🤷🏻♂️. It was a single output supply, when needed I hooked up additional buck- or...
Help identifying jst connector (discuss.tchncs.de)
I'm working on adding extra access control to elevator calling buttons and i would like to identify the connector type of the wires connecting elevator buttons to the elevator panel...
Welcome to Electronics
This Lemmy community is an alternative to the Reddit /r/Electronics
Which community in lemmy is similar to r/buildmeaPC?
Soon I’ll need help building a new PC. Thanks!
Riser mount for smd component
I did not know about this mounting method. Probably it’s a way to improve passive cooling capabilities?...
Struggling to find a PCIe USB controller IC. Either unavailable or expensive
I want to use an IC that will take x4 3.0 PCIe lanes, and adds a USB 3.1 controller....
The first double sided board I made at home :) (lemmy.world)
I’m currently working on a more complex project that uses double sided assembly (and a weird USB-C connector). To practice these things a little, I ordered some low cost boards to get used to that connector and explore double sided reflow (which seems easier than I expected)....
I need a new bench power supply
Hello, I did manage to kill my cheap-ish bench supply causing it to randomly output up to like 300% the set voltage when under load which did already kill one board. Probably I didn’t actively kill it but the chinesium did its job 🤷🏻♂️. It was a single output supply, when needed I hooked up additional buck- or...