askelectronics

Serious question from a beginner in electronics. For reasons I do not fully understand, I have become fixated on the idea of collecting small amounts of electricity from “interesting” sources. I don’t mean “free energy”, instead, I mean things like extracting a few mV from being so close to a AM radio tower using two...

Hi, I have built a microvawe transformer spotwelder, I have put a single turn of welder wire for in the secondary and I’m timing it with arduino. Worth mentioning it was/is a 230V transformer. Electrodes are sharpened copper rods. I believe the voltage is still high. The spotwelds it produces are slightly discolored and not as...

Im building a flashlight and i want to test if a fan in it would be a good idea but the flashlight is really small so i would need a motor thats smaller than 1 cm preferably. I found really good ones at maxon group but unless you order them in bulk(1000+ units) they cost like 400€. So do yall know anywhere i could find them?...

Hello y’all! I’ve always been interested in computers and programming for as long as i can remember, but recently i’ve decided to try to get into some of the deeper stuff behind that, into the wonderful world of electronics. Where should I start? What courses or books or youtube series should I consume? What are some...

Do any of you have experienced good products for tinkering together with a 3 year old?...

So, there are these great 32700 LiFePO4 batteries that showed up in my local industrial market. For like USD 2$!...

Hello, we are making a thesis where we use MOSFETs as an alternative radiation detector. So to explain it, it works when the mosfet is irradiated with an external radiation source; its voltage threshold increases, which will be used to determine the radiation dose. I'm currently asking for help on how we measure the voltage...

Hi everyone! Recently I have gotten interested in communication protocols and have been looking for one (with little success, hence my question) which would satisfy the following requirements (in prioritized order):...

Hello, I have a circuit that will need to return connected hardware to a default state if power is lost. The hardware can handle continuous voltage, so I’m thinking a simple solution would be to use a battery to provide that fallback power source. To avoid draining the battery, I’d like to connect it through a relay on the...

I purchased an e-bike which was advertised as just needing the batteries replaced. The li-ion batteries had been sitting dead for months. Once I got the battery removed it was clear that was not the case. You can see the hole where the plastic melted from this component overheating on the board. The burnt one is the same as...

Pretty basic question but I am struggling to find the words to get the correct search result. The soldering iron I bought came with very narrow tips that I think are supposed to be used for circuit boards and components....

I'm planning to add a momentary switch to a single loop DC circuit. Will this cause any amount of resistance in the circuit? I'm a complete noobie when it comes to electronics, any resource links or clarification is appreciated. I know the type of material/width of wire and a pot will cause resistance but will any component put...

I have a 3D printer and have a special filter that has two 24V blower fans that are connected in parallel. Unfortunately my printer doesn’t have the proper connectors for the fans. So if I purchase something like this power jack adapter I know the adapter is 12V not sure if that would make a difference. Anyway if I connect the...

I am curious if one, something like this exists, and two what the cost might be? I am looking for a screen, I assume an e-ink is the best/cheapest option and I want it to be as close as possible to the size of a playing card, ideally not thicker than 2MM. But I think up to 5mm could work....

I’m interested in learning how to make a proper PCB rather than perf board with wires all over the place.

I want to replace one half of this with longer wire, but I am not confident about the name of the connector used....

I have two led strips used for 2x27" monitor bias lighting. Each have their own USB cables for power. These two USB cables are plugged into a 2-port wall charger for a phone. I would like to use a 2x female to 1x male adapter to join the two USB cables into one, then plug it into a much smaller 1-port USB wall charger. The...

I’m trying to use an RPi Pico W as a temp/humidity sensor using a DHT20....

I am powering a 5V microcontroller (arduino clone, atmega328p) using a 9V block and a buck converter. Now I want to let the microcontroller occasionally measure the battery voltage, so I can get an idea of how full it is....

I’ve recently bought a used computer, and it has a few problems. I’m looking for a guide to help me identify which parts are causing the problem....

Currently, only one company in the world – ASML – has the technological capability necessary for the creation of photolithography machines which are sufficient for the production of modern semiconductor devices. What I’m wondering is at what point does semiconductor manufacturing become practical, or even feesible for...

I’m trying to build a esp8266 weather station and got some MCP1700-3302E to power the esp8266 from a lipo. But when I connect the lipo to the MCP1700 (looking at it flat spot at the front, ground left, Vin in the middle and Vout on the right) I get no output at Vout. I googled and could not find anything. I tested 5 different...

Disclaimer: this is not specifically for a commercial product, but various things I design sometimes get commercialized. I mention this so that you may decide whether you want to weigh in. If it’s commercialized, I will probably make very little money but a bunch of university students may get a neat STEM program in the...

Hey all, have I damaged this xbox 360 controller circuit board beyond repair?...